史萊姆論壇

史萊姆論壇 (http://forum.slime.com.tw/)
-   系統 & 硬體安裝及故障判斷技術文件 (http://forum.slime.com.tw/f134.html)
-   -   電腦各種錯誤訊息的中文意思 (http://forum.slime.com.tw/thread167971.html)

psac 2006-02-11 01:02 AM

電腦各種錯誤訊息的中文意思
 
電腦各種錯誤訊息的中文意思

一、BIOS中的提示訊息

提示訊息 說明
Drive A error 驅動器A錯誤
System halt 系統掛起
Keyboard controller error 鍵盤控制器錯誤
Keyboard error or no keyboard present 鍵盤錯誤或者鍵盤不存在
BIOS ROM checksum error BIOS ROM 校驗錯誤
Single hardisk cable fail 當硬碟使用Cable選項時硬碟安裝位置不正確
FDD Controller Failure BIOS 軟碟控制器錯誤
HDD Controller Failure BIOS 硬碟控制器錯誤
Driver Error 驅動器錯誤
快取 Memory Bad, Do not Enable 快取 高速快取快取損壞,不能使用
Error: Unable to control A20 line 錯誤提示:不能使用A20位址控制線
Memory write/Read failure 記憶體讀寫失敗
Memory allocation error 記憶體定位錯誤
CMOS Battery state Low CMOS沒電了
Keyboard interface error 鍵盤接頭錯誤
Hard disk drive failure 載入硬碟失敗
Hard disk not present 硬碟不存在
Floppy disk(s) fail (40) 軟碟機載入失敗,一般是資料線插反,電源線沒有插接,CMOS內部軟式磁碟機設定錯誤
CMOS checksum error-efaults loaded. CMOS校驗錯誤,裝入預設(預設)設定

  二、BIOS重新整理失敗後,Bootblock啟動時出現的提示訊息

提示訊息 說明
Detecting floppy drive A media... 檢測軟式磁碟機A的格式
Drive media is : 1.44Mb1.2Mb 720Kb 360K 驅動器格式是1.44Mb、12Mb、720kb、360kb的一種
DISK BOOT FAILURE, INSERT SYSTEM DISK AND PRESS ENTER 磁牒啟始失敗,插入系統碟後按任意鍵繼續

  三、MBR主啟始區提示訊息

提示訊息 說明
Invalid partition table 無效的分區表
Error loading operating sy stem 不能裝入啟始系統
Missing operating system 系統啟始文件丟失掉

  說明:如果在電腦啟動程序中,在硬體組態清單下方(也就時在平時正常啟動時出現Starting Windows 98…的地方)出現不可識別字元,此時可判斷硬碟分區表損壞。如果你的硬碟上有重要資料,這時你不要輕易進行分區,可找專業的資料恢復公司。
  四、DOS活動分區中的提示訊息

提示訊息 說明
Invalid system disk 無效的系統碟
Disk I/O error, Replace the disk and press any key. 磁牒I/O錯誤,取代磁牒後按任意鍵(當C碟系統檔案丟失掉或被破壞時出現該提示訊息。這時可能SYS C:為修復系統檔案)
Invalid Media Type reaching Drive C: 無效的C盤媒體格式說明。也就是C碟沒有格式化或者是其他操作系統的磁牒格式如NTFS
Invalid Boot Diskette Boot Failure 無效的啟動碟,啟動失敗

  五、IO.SYS中的提示訊息

提示訊息 說明
Insert diskette for drive and press any key when ready 插入磁牒到驅動器中後按任意鍵
Your program caused a divide overflow error
If the problem persists, contact your program vendor 你的程序導致溢位錯誤。如果該問題還存在,請聯係你的程序供應商
Windows has disabled direct disk access to protect your long filenames Windows不能直接訪問受保護的長檔案名
The system has been halted. Press Ctrl+Alt+Del to restart your computer 系統掛起,按Ctrl+Alt+Del重新啟動你的電腦
You started your computer with a version of MS-DOS incompatible with this version of Windows. Insert a Startup diskette matching this version of Windows and then restart 你啟動的MS-DOS版本與Windows版本不相容,請插入與Windows版本匹配的系統碟後再重啟
This version of Windows requires a 386 or better processor 該Windows版本需要386以後的CPU支持
A20 hardware error. Contact technical support to identify the problem 位址線A20錯誤。聯係技術支持來識別該問題
Starting Windows 98... 正在啟動Windows 98……
Windows 98 is now starting your MS-DOS-based program Windows 98正在啟動關於MS-DOS的程序
Windows 98 is now restarting... Windows 98正在重新啟動
Press Esc now to cancel MS-DOS mode and restart Windows 98... 按Esc結束MS-DOS 模式,重新啟動Windows 98…
There is an unrecognized command in your CONFIG.SYS file 在你的CONFIG.SYS文件中有不可識別的指令
The following command in your CONFIG.SYS file is incorrect: 在你的CONFIG.SYS有下列錯誤指令
The sector size specified in this file is too large: 該檔案中指定的扇區太大
The following file is missing or corrupted: WIN.COM COMMAND.COM 下列文件丟失掉或被破壞:WIN.COM和COMMAND.COM
There is an invalid country code or code page in your CONFIG.SYS file 在你的CONFIG.SYS裡有一個無效的國家程式碼
There is an error in the COUNTRY command in your CONFIG.SYS file 在你的CONFIG.SYS裡有一個錯誤的設定國家指令
There is not enough memory for the COUNTRY.SYS file 沒有足夠的記憶體來載入COUNTRY.SYS文件
Remove some drivers from your CONFIG.SYS file, and then try again 請從CONFIG.SYS文件中移除部分驅動程式,然後再試
Remove some drivers, and then try again 去除一些驅動程式,然後再試。這裡的驅動程式是指在CONFIG.SYS中使用device或devicehigh指令載入的程式文件
Remove some disk drivers from your CONFIG.SYS file, and then try again 從你的(CONFIG.SYS)移去部分程序,然後再試
The configuration specified in your CONFIG.SYS file is too large for memory 調整你的CONFIG.SYS文件以獲得足夠大的記憶體
You have too many block devices specified in your CONFIG.SYS file 調整你的CONFIG.SYS文件以獲得block devices
The STACKS setting(s) in your CONFIG.SYS file are incorrect 在你的CONFIG.SYS中堆疊設定不正確
Default stack settings will be used instead 預設的堆疊設定將被替代使用
There is an error in your CONFIG.SYS file on line XX 在你的CONFIG.SYS裡XX行錯誤
Warning: Logical drives past Z exist and will be ignored 警告:邏輯磁碟機Z已經存在,將被忽略
Type the name of the Command Interpreter (e.g., C:\WINDOWS\COMMAND.COM) Press any key to continue… 請輸入指令解釋器的檔案名(如:C:\WIN DOWS\COMMAND.COM)後,按任意鍵繼續
Windows is bypassing your startup files
Minimal network support will be loaded if available Windows正在跳過你的啟動檔案。如果網路可用,最小網路支持將被載入
Windows is starting the command prompt only Windows正在啟動指令字元模式
Windows will prompt you to confirm each startup command Windows將提示你驗證每一個啟動指令
The compression driver cannot be set up correctly 壓縮驅動程式不能被正確載入
Get a version from your vendor that is compatible with this version of Windows 從你的供應商那裡獲得一個與Windows版本相相容的版本
Process the system registry 執行系統註冊表
Create a startup log file (BOOTLOG.TXT) 新增啟動日誌BOOTLOG.TXT文件
Process your startup device drivers (CONFIG.SYS) 執行CONFIG.SYS文件中的設備驅動
Process your startup command file (AUTOEXEC.BAT) 執行AUTOEXEC.BAT中的啟動指令
Load the Windows graphical user interface 裝入WINDOWS圖形用戶界面(GDI)
Warning: Windows has detected a registry/configuration error. Choose, Command prompt only, and run SCANREG 警告:Windows檢測到一個註冊表或組態錯誤選項DOS操作模式,執行SCANREG
Warning: Windows has detected a compressed drive access error. Choose Safe mode command prompt only, to help you identify the problem 警告:Windows檢測到一個訪問壓縮驅動器錯誤,選項安全模式下的MS-DOS,來說明 你識別這個問題
Warning: Windows did not finish loading on the previous attempt. Choose Safe mode, to start Windows with a minimal set of drivers 警告:Windows在剛才嘗試後不能夠完成載入,選項安全模式,用最小驅動啟動你的電腦
Warning: Windows multi-boot may not function correctly
Check for system files in your root directory with conflicting extensions 警告:Windows不能夠正確完成多系統啟動,在你的ROOT目錄裡檢查不一致的系統檔案
Warning: the system configuration manager failed to run. Some of your real-mode device drivers may not initialize properly 警告:系統管理器執行失敗,一些真實模式驅動可能沒有正確啟始化
The BUFFERS setting(s) in your CONFIG.SYS file are too large. Default buffer settings will be used instead 在你的CONFIG.SYS裡BUFFER設定太大。預設的BUFFER緩衝器設定將被使用
A memory allocation error occurred during startup<BR< p>
>Restart your computer and select Interactive Start to identify the problem 在啟動程序中記憶體分配發生錯誤,請重新啟動你的電腦然後選用交互式方式啟動來確定故障原因
Warning: the high memory area (HMA) is not available Additional low memory (below 640K) will be used instead 警告:高端記憶體不可用,低端記憶體將被替代使用
There is not enough memory for Windows. Remove some drivers from your CONFIG.SYS file, and then try again 對Windows來說沒有足夠的記憶體,請從CONFIG.SYS文件中移去部分載入的程序,然後再試著啟動你的讀入電腦
Your previous MS-DOS files were not found. 舊的MS-DOS文件沒有找到,這一般於使用雙啟動的系統,另一個系統是DOS6
Your previous MS-DOS version is not supported. MS-DOS startup failed 舊的MS-DOS版本不支持。MS-DOS啟動失敗
Now loading your previous version of MS-DOS, please wait 現在正在載入舊的MS-DOS版本,請等待
Invalid setting in the MSDOS.SYS file:An internal stack overflow has caused this session to be halted MSDOS.SYS文件中無效的設定選項。系統堆疊溢位,系統掛起
Change the STACKS setting in your CONFIG.SYS file, and then try again 請改變CONFIG.SYS文件中的STACK設定,然後再試
Stack overflow 堆疊溢位
Integer divide by 0  整數被0除
Not enough space for environment  沒有足夠的空間
Run-time error 執行錯誤
Floating-point support not loaded  浮點運算支持沒有裝入
Null pointer assignment  無效的斷點分配

psac 2006-02-11 01:05 AM

六、COMMAND中的提示訊息

提示訊息 說    明
Stack overflow 堆疊溢位
Integer divide by 0 分母是0
Not enough space for environment 磁牒沒有足夠的空間
Run-time error 時鍾錯誤
No fixed disks present 沒有硬碟存在
Insufficient memory 記憶體不足
Invalid drive specification 無效的驅動器名
Invalid characters in volume label 無效的磁碟代號
Invalid Volume ID 無效的卷冊ID號
No target drive specified 目標驅動器沒有定義
missing operating system 系統檔案丟失掉
Non system Disk or Disk Error 不是系統碟或磁牒錯誤
Replace Disk and Press Anykey To Reboot 取代磁牒,按任意鍵重新啟動

  七、SYS傳送系統檔案時的提示訊息

提示訊息 說    明
Cannot find System Files 不能找到系統檔案
System transferred 系統傳送完畢
Disk unsuitable for system disk 目標磁牒不適合做系統碟

  八、FORMAT中的提示訊息

提示訊息 說    明
Unable to write BOOT. 不能寫啟始扇區
Invalid media type 無效的磁牒檔案類型
Parameters not supported 參數不支持
Cannot format a network drive 不能格式化網路驅動器
Invalid media or Track 0 bad - disk unusable 無效的磁牒或0磁軌損壞,磁牒不可用
Format terminated 格式化終止
Disk Boot failure 磁牒BOOT區錯誤
Invalid system disk 無效的系統磁牒
Disk I/O error,Replace the disk, and then
press any key 磁牒I/O錯誤,請換盤後按任意鍵。通常在讀寫軟碟時出現此類錯誤
Non-System disk or disk error,Replace and strike any key when ready 無系統的磁牒或磁牒錯誤,請取代後按任意鍵
Too many open files 開啟的文件太多
Access denied Insufficient memory 沒有足夠的記憶體訪問被拒絕
Invalid drive specification 無效的磁碟代號說明
Parse Error XX 分析錯誤 XX
Incorrect MS-DOS version 不正確的MS-DOS版本
X% percent completed 格式化正在進行,已經完成X%
Format complete. 格式化完成
XX bytes in bad sectors XX字元的壞扇區
XX bytes total disk space 磁牒的全睰占湮猉X字元
XX bytes available on disk 磁牒的可使用空間為XX字
Volume label (11 characters, ENTER for none)? 請輸入磁牒卷冊(總共11個字元,按Enter鍵為空)
Format not supported on drive X Format指令不支持驅動器X
Invalid device parameters from device driver 無效的設備驅動參數
Error writing FAT 寫FAT表錯誤
Error writing directory 寫DIR目錄表錯誤
Cannot format an ASSIGN or SUBST drive 不能格式化ASSIGN和SUBST指定的驅動器
Cannot find System Files 沒有找到系統檔案
Cannot format a network drive 不能格式化網路驅動器
Invalid characters in volume label 磁牒卷冊中存在非法字元
Parameters not supported 參數不支持
Format terminated 格式化意外終止
Disk unsuitable for system disk 這個磁牒不適合作為系統碟
Unable to write BOOT 不能寫BOOT區
Error reading directory 讀DIR目錄區錯誤
No target drive specified 目的驅動器沒有說明
and press ENTER when ready 準備好後按Enter鍵鍵
System transferred 系統傳送完畢
Enter current volume label for drive X 請為驅動器X輸入磁牒的卷冊
Parameters not compatible with fixed disk 參數與硬碟不相容
Volume Serial Number is XXXX 分區格式化時隨機產生的序列號是:XXXX
Format broken 格式化被強行終止
Format not available on drive XX 不能在驅動器XX上使用格式化指令
on-System disk or disk error 沒有系統碟或磁牒錯誤
Bad Partition Table 錯誤的硬碟分區表
Parameters not supported by drive 該驅動器不支持這些參數
Insert DOS disk in drive A 請在驅動器A中插入DOS系統碟
WARNING, ALL DATA ON NON-REMOVABLE DISK DRIVE %1: WILL BE LOST! Proceed with 警告:硬碟分區X中的所有資料都將丟失掉,確定執行格式化指令嗎?
Format another (Y/N)?! 還格式化其他盤嗎
Error reading partition table 讀硬碟分區表錯誤
Error writing partition table 寫硬碟分區表錯誤
Parameters not compatible 參數不匹配
XX allocation units available on disk 磁牒上有XX可用簇
XX bytes in each allocation unit 每個簇有大小為XX字元
Same parameter entered twice 相同的參數被輸入兩次
Must enter both /T and /N parameters /T和/N參數必須同時使用
There is not enough room to create a restore file 沒有足夠的空間來建立恢覆文件
You will not be able to use the UNFORMAT utility 你將不能使用UNFORMAT工具來恢復你的硬碟資料
There is not enough disk space for system files 沒有足夠的空間來儲存於系統檔案
This disk cannot be unformatted 這個磁牒不能被反格式化
There was an error creating the format recovery file 在建立恢覆文件時產生了一個錯誤
Volume label is not supported with /8 parameter 該驅動器不支持/8參數
Insufficient memory to load system files 沒有足夠的記憶體裝入系統檔案
Insufficient memory. 記憶體不足
Calculating free space (this may take several minutes)... 正在統計磁牒空間(可能要花上幾分鍾時間)

  九、FDISK中的提示訊息

提示訊息 說    明
Delete Primary DOS Partition 移除主DOS分區
Delete Extended DOS Partition 移除增強DOS分區
Delete Logical DOS Drive(s) in the Extended DOS Partition 移除邏輯DOS分區
WARNING! Data in the deleted Primary DOS Partition will be lost 警告:主DOS分區的資料將全部丟失掉
WARNING! Data in the deleted Extended DOS Partition will be lost. Do you wish to continue (Y/N)? 警告:延展分區中的資料將全部丟失掉,你真的繼續嗎
Delete Logical DOS Drive(s) in the Extended DOS Partition 移除延展分區下的邏輯分區
WARNING! Data in a deleted Logical DOS Drive will be lost What drive do you want to delete? Are you sure (Y/N)? 警告:邏輯分區中的所有資料都將丟失掉,你移除哪個驅動器?你真的確定嗎
Display Partition Information 顯示分區內容訊息
The Extended DOS Partition contains Logical DOS Drives. 增強DOS分區中包含DOS邏輯分區
Do you want to display the logical drive information (Y/N)? 你想顯示邏輯分區的訊息嗎
Display Logical DOS Drive Information 顯示邏輯分區訊息
Enter partition size in Mbytes or percent of disk space (%) to create a Primary DOS Partition... 輸入所建立主DOS分區的容量,服務機構是百分比
Enter logical drive size in Mbytes or percent of disk space (%)... 請輸入邏輯分區容量大小或磁牒空間的百分比
Enter Volume Label? 請輸入卷冊
Enter partition size in Mbytes or percent of disk space (%)to create an Extended DOS Partition.... 請輸入增強DOS分區的容量大小或磁牒空間的百分比
Do you wish to use the maximum available size for a Primary DOS Partition 你想使用全部磁牒空間作為主DOS分區嗎
Change Current Fixed Disk Drive . Enter Fixed Disk Drive Number (X) 當你掛接兩個以上硬碟時,在FDISK的系統功能表中將多一個第5項,選項第5項時,將提示:請輸入硬碟的序號
Fixed Disk Drive Status 硬碟狀態

psac 2006-02-11 01:06 AM

Data in the deleted Primary DOS Partition will be lost.What primary partition do you want to delete?Do you wish to continue (Y/N)? DOS主分區中的資料將全部丟失掉。你準備移除哪個主分區?你想繼續嗎
Data in the deleted Non-DOS Partition will be lost.What Non-DOS partition do you want to delete?Do you wish to continue (Y/N)? 非DOS分區的資料將全部丟失掉。你準備移除哪一個非DOS分區?你要繼續嗎
You MUST restart your system for your changes to take effect 你必須重新啟動你的電腦你所做的所有改變才有效
Any drives you have created or changed must be formatted 你新增的分區或改變的分區必須被格式化後才可用
Shut down Windows before restarting 在重啟之前請關閉Windows
Your computer has a disk larger than 512 MB. This version of Windows includes improved support for large disks, resulting in more efficient use of disk space on large drives, and allowing disks over 2 GB to be formatted as a single drive 你的電腦掛接了一個大於512M的硬碟。該版本的Windows支持大硬碟,能夠更有效的使用大硬碟上的磁牒空間,並充許單個分區大於2GB
Press Esc to exit FDISK 按Esc結束FDISK
This drive is FAT16 by default, switch to FAT32 (Y/N)? 這個驅動器預設是FAT16模式,真的轉換為FAT32模式嗎
This drive must be FAT32 because its size is > 2048 MB 當分區的空間大於2048MB時,這個分區必須使用FAT32磁牒資料格式
This drive must be FAT16 because its size is too small to be FAT32 因為這個分區對於FAT32格式來說太小,所以這個分區只能使用FAT16格式
Verifying drive integrity, complete 正在校驗分區的完整性,完成
Your computer has NTFS partitions which may require large drive support. If you are using another operating system, such as Windows NT, which supports large drives you should enable treating these partitions as large 你的電腦有一個NTFS分區可能需要大分區支持,如果你正在使用其他操作系統,如Windows NT,你應該把這些分區分大一些
NOTE: If you answer Y and the partition display looks incorrect or a hang or crash occurs do nothing, run FDISK again, and answer N to this question 注意:如果你回答Y,可能顯示的分區訊息看上去不正確或系統掛起或什麼動作也沒有,這時你可再次執行FDISK,對這個問題用N回答
Should NTFS partitions on all drives be treated as large (Y/N)? 對所有的NTFS分區使用大分區模式
Drive deleted 驅動器被移除
Partition made active 分區X被設定為活動
Primary DOS Partition created 主DOS分區被建立
Extended DOS Partition created 增強DOS分區被建立
Logical DOS Drive created, drive letters changed or added 邏輯分區被建立,驅動器的磁碟代號可能被改變或有新的增加
No partitions defined 沒有分區被定義
No logical drives defined 沒有邏輯磁碟機被說明
Drive letters have been changed or deleted 驅動器磁碟代號已經被改變或移除
No active partitions 沒有設定活動分區,該硬碟不能被啟動
No fixed disks present 沒有硬碟
Error reading fixed disk 讀硬碟錯誤
Error writing fixed disk 寫硬碟錯誤
Write protect error writing fixed disk 寫硬碟寫保護錯誤
Incorrect DOS version 不正確的DOS版本
Cannot FDISK with network loaded 不能對網路驅動器使用FDISK
No space to create a DOS partition 沒有足夠的空間建立DOS分區
Requested logical drive size exceeds the maximum available space 輸入的邏輯磁碟機的容量超過了最大可用的磁牒空間容量
Requested partition size exceeds the maximum available space 輸入的分區的容量超過了最大可用的磁牒空間容量
No partitions to delete 已經沒有分區可以被移除
The only startable partition on Drive is already set active 硬碟X上的惟一的可啟動分區已經被標記為活動(延展分區不能被設定為活動)
No partitions to make active 沒有分區可以被標記為活動分區
Partition selected is not startable, active partition not changed 輸入的分區X不可啟動,現用的活動分區沒有被改變
Cannot create Extended DOS Partition without Primary DOS Partition on disk X 在硬碟X上沒有主DOS分區時不能建立增強DOS 分區
All available space in the Extended DOS Partition is assigned to logical drives 延展分區的全部有效空間都分配給邏輯磁碟機嗎?還可以再分為主分區或其他分區
Cannot delete Extended DOS Partition while logical drives exist 因為延展分區下有邏輯分區存在,所以延展分區不能被移除
All logical drives deleted in the Extended DOS Partition is not a choice. Please enter X 確定移除哪一個邏輯分區,請輸入X
WARNING! The partition set active is not startable 警告:被設定為活動的分區是不可啟動的
Only non-startable partitions exist 只有不可啟動的分區存在
Only partitions on Drive 1 can be made active 只有硬碟1上的分區可被設定為活動。當你掛接兩個以上硬碟時,使用FDISK指令時只能設定硬碟1中的某個主分區為活動,其他硬碟上的主分區都不能設定為活動
Maximum number of Logical DOS Drives installed 邏輯磁碟機的所有磁碟代號都使用,意思是你在分區時驅動器的磁碟代號超過了Z
Cannot create a zero size partition 不能建立大小空間為0的分區
Unable to access Drive X 不能訪問驅動器X
Cannot delete Primary DOS Partition on drive 1 when an Extended DOS Partition exists 當延展分區存在時不能移除硬碟1上的主DOS分區
Invalid entry 無效的輸入
Volume label does not match 標不匹配。當你移除分區時,系統會提示輸入該分區的卷冊,如果輸入的卷冊和你要移除的分區的卷冊不一致時,操作將不能進行
Cannot create Logical DOS Drive without an Extended DOS Partition on the current drive 沒有延展分區時不能在當前硬碟上建立邏輯磁碟機
Could not change partitions, because the disk could not be locked 不能改變分區,因為該硬碟不能被鎖定
Internal error 內部錯誤
Incorrect MS-DOS version 不正確的MS-DOS版本
Invalid parameter 無效的參數
Cannot FDISK with network loaded 不能對網路驅動器進行FDISK
The master boot code has NOT been updated
/STATUS Displays partition information 主啟始區程式碼沒有被更新。顯示分區訊息
/X Ignores extended disk-access support. Use this switch 不使用增強磁牒訪問指令支持。當你使用
if you receive disk access or stack overflow messages 這個參數時你將看到堆疊溢位的訊息
/MBR and /CMBR cannot both be specified /MBR和/CMBR這兩個參數不能同時使用
/MBR only operates on drive 1,use /CMBR for other drives 只能對硬碟1使用,/CMBR對其他硬碟使用/MBR
You must specify a drive number with /CMBR
Invalid partition table 在使用/CMBR參數時必須說明硬碟的序號。無效的硬碟分區表
Error loading operating system 在裝入操作系統時錯誤
Missing operating system 操作系統檔案丟失掉
stack overflow 堆疊溢位
integer divide by 0 整數被0除
run-time error 執行錯誤
not enough space for environment 沒有足夠的空間 -----

六翼黑帝斯 2006-02-11 08:35 PM

感謝大大分享~
剛好找到我想要找的東西~
Floppy disk(s) fail (40) 軟碟機載入失敗,一般是資料線插反,電源線沒有插接,CMOS內部軟式磁碟機設定錯誤
不過是最近才這樣~
按重新開始鍵就又好了~

psac 2006-08-22 06:38 PM

電腦各種錯誤訊息的中文意思

一、BIOS中的提示訊息

提示訊息 說明
Drive A error 驅動器A錯誤
System halt 系統掛起
Keyboard controller error 鍵盤控制器錯誤
Keyboard error or no keyboard present 鍵盤錯誤或者鍵盤不存在
BIOS ROM checksum error BIOS ROM 校驗錯誤
Single hardisk cable fail 當硬碟使用Cable選項時硬碟安裝位置不正確
FDD Controller Failure BIOS 軟碟控制器錯誤
HDD Controller Failure BIOS 硬碟控制器錯誤
Driver Error 驅動器錯誤
Cache Memory Bad, Do not Enable Cache 高速快取記憶體Cache損壞,不能使用
Error: Unable to control A20 line 錯誤提示:不能使用A20地址控制線
Memory write/Read failure 記憶體讀寫失敗
Memory allocation error 記憶體定位錯誤
CMOS Battery state Low CMOS沒電了
Keyboard interface error 鍵盤接頭錯誤
Hard disk drive failure 載入硬碟失敗
Hard disk not present 硬碟不存在
Floppy disk(s) fail (40) 軟碟驅動器載入失敗,一般是資料線插反,電源線沒有插接,CMOS內部軟式磁碟機設置錯誤
CMOS checksum error-efaults loaded. CMOS校驗錯誤,裝入預設(預定)設置

  二、BIOS重新整理失敗後,Bootblock啟動時出現的提示訊息

提示訊息 說明
Detecting floppy drive A media... 檢測軟式磁碟機A的格式
Drive media is : 1.44Mb1.2Mb 720Kb 360K 驅動器格式是1.44Mb、12Mb、720kb、360kb的一種
DISK BOOT FAILURE, INSERT SYSTEM DISK AND PRESS ENTER 磁碟啟始失敗,插入系統硬碟後按任意鍵繼續

  三、MBR主啟始區提示訊息

提示訊息 說明
Invalid partition table 無效的分區表
Error loading operating sy stem 不能裝入啟始系統
Missing operating system 系統啟始文件丟失

  說明:如果在電腦啟動過程中,在硬體配置清單下方(也就時在平時正常啟動時出現Starting Windows 98…的地方)出現不可識別字元,此時可判斷硬碟分區表損壞。如果你的硬碟上有重要資料,這時你不要輕易進行分區,可找專業的資料恢復公司。
  四、DOS活動分區中的提示訊息

提示訊息 說明
Invalid system disk 無效的系統硬碟
Disk I/O error, Replace the disk and press any key. 磁碟I/O錯誤,替換磁碟後按任意鍵(當C硬碟系統文件丟失或被破壞時出現該提示訊息。這時可能SYS C:為修復系統文件)
Invalid Media Type reaching Drive C: 無效的C盤媒體格式說明。也就是C硬碟沒有格式化或者是其他操作系統的磁碟格式如NTFS
Invalid Boot Diskette Boot Failure 無效的啟動碟,啟動失敗

  五、IO.SYS中的提示訊息

提示訊息 說明
Insert diskette for drive and press any key when ready 插入磁碟到驅動器中後按任意鍵
Your program caused a divide overflow error
If the problem persists, contact your program vendor 你的程式導致溢出錯誤。如果該問題還存在,請聯繫你的程式供應商
Windows has disabled direct disk access to protect your long filenames Windows不能直接訪問受保護的長文件名
The system has been halted. Press Ctrl+Alt+Del to restart your computer 系統掛起,按Ctrl+Alt+Del重新啟動你的電腦
You started your computer with a version of MS-DOS incompatible with this version of Windows. Insert a Startup diskette matching this version of Windows and then restart 你啟動的MS-DOS版本與Windows版本不相容,請插入與Windows版本匹配的系統硬碟後再重啟
This version of Windows requires a 386 or better processor 該Windows版本需要386以後的CPU支持
A20 hardware error. Contact technical support to identify the problem 地址線A20錯誤。聯繫技術支持來識別該問題
Starting Windows 98... 正在啟動Windows 98……
Windows 98 is now starting your MS-DOS-based program Windows 98正在啟動基於MS-DOS的程式
Windows 98 is now restarting... Windows 98正在重新啟動
Press Esc now to cancel MS-DOS mode and restart Windows 98... 按Esc退出MS-DOS 模式,重新啟動Windows 98…
There is an unrecognized command in your CONFIG.SYS file 在你的CONFIG.SYS文件中有不可識別的命令
The following command in your CONFIG.SYS file is incorrect: 在你的CONFIG.SYS有下列錯誤命令
The sector size specified in this file is too large: 該文件中指定的扇區太大
The following file is missing or corrupted: WIN.COM COMMAND.COM 下列文件丟失或被破壞:WIN.COM和COMMAND.COM
There is an invalid country code or code page in your CONFIG.SYS file 在你的CONFIG.SYS裡有一個無效的國家代碼
There is an error in the COUNTRY command in your CONFIG.SYS file 在你的CONFIG.SYS裡有一個錯誤的設置國家命令
There is not enough memory for the COUNTRY.SYS file 沒有足夠的記憶體來載入COUNTRY.SYS文件
Remove some drivers from your CONFIG.SYS file, and then try again 請從CONFIG.SYS文件中刪除部分驅動程式,然後再試
Remove some drivers, and then try again 去除一些驅動程式,然後再試。這裡的驅動程式是指在CONFIG.SYS中使用device或devicehigh命令載入的程式文件
Remove some disk drivers from your CONFIG.SYS file, and then try again 從你的(CONFIG.SYS)移去部分程式,然後再試
The configuration specified in your CONFIG.SYS file is too large for memory 調整你的CONFIG.SYS文件以獲得足夠大的記憶體
You have too many block devices specified in your CONFIG.SYS file 調整你的CONFIG.SYS文件以獲得block devices
The STACKS setting(s) in your CONFIG.SYS file are incorrect 在你的CONFIG.SYS中堆疊設置不正確
Default stack settings will be used instead 預設的堆疊設置將被替代使用
There is an error in your CONFIG.SYS file on line XX 在你的CONFIG.SYS裡XX行錯誤
Warning: Logical drives past Z exist and will be ignored 警告:邏輯驅動器Z已經存在,將被忽略
Type the name of the Command Interpreter (e.g., C:\WINDOWS\COMMAND.COM) Press any key to continue… 請輸入命令解釋器的文件名(如:C:\WIN DOWS\COMMAND.COM)後,按任意鍵繼續
Windows is bypassing your startup files
Minimal network support will be loaded if available Windows正在跳過你的啟動文件。如果網路可用,最小網路支持將被載入
Windows is starting the command prompt only Windows正在啟動命令字元模式
Windows will prompt you to confirm each startup command Windows將提示你確認每一個啟動命令
The compression driver cannot be set up correctly 壓縮驅動程式不能被正確載入
Get a version from your vendor that is compatible with this version of Windows 從你的供應商那裡獲得一個與Windows版本相相容的版本
Process the system registry 執行系統註冊表
Create a startup log file (BOOTLOG.TXT) 創建啟動日誌BOOTLOG.TXT文件
Process your startup device drivers (CONFIG.SYS) 執行CONFIG.SYS文件中的設備驅動
Process your startup command file (AUTOEXEC.BAT) 執行AUTOEXEC.BAT中的啟動命令
Load the Windows graphical user interface 裝入WINDOWS圖形用戶界面(GDI)
Warning: Windows has detected a registry/configuration error. Choose, Command prompt only, and run SCANREG 警告:Windows檢測到一個註冊表或配置錯誤選擇DOS操作模式,執行SCANREG
Warning: Windows has detected a compressed drive access error. Choose Safe mode command prompt only, to help you identify the problem 警告:Windows檢測到一個訪問壓縮驅動器錯誤,選擇安全模式下的MS-DOS,來幫助你識別這個問題
Warning: Windows did not finish loading on the previous attempt. Choose Safe mode, to start Windows with a minimal set of drivers 警告:Windows在剛才嘗試後不能夠完成載入,選擇安全模式,用最小驅動啟動你的電腦
Warning: Windows multi-boot may not function correctly
Check for system files in your root directory with conflicting extensions 警告:Windows不能夠正確完成多系統啟動,在你的ROOT目錄裡檢查不一致的系統文件
Warning: the system configuration manager failed to run. Some of your real-mode device drivers may not initialize properly 警告:系統管理器執行失敗,一些實模式驅動可能沒有正確初始化
The BUFFERS setting(s) in your CONFIG.SYS file are too large. Default buffer settings will be used instead 在你的CONFIG.SYS裡BUFFER設置太大。預定的BUFFER緩衝器設置將被使用
A memory allocation error occurred during startup<BR< p>
>Restart your computer and select Interactive Start to identify the problem 在啟動過程中記憶體分配發生錯誤,請重新啟動你的電腦然後選用交互式方式啟動來確定故障原因
Warning: the high memory area (HMA) is not available Additional low memory (below 640K) will be used instead 警告:高端記憶體不可用,低端記憶體將被代替使用
There is not enough memory for Windows. Remove some drivers from your CONFIG.SYS file, and then try again 對Windows來說沒有足夠的記憶體,請從CONFIG.SYS文件中移去部分載入的程式,然後再試著啟動你的讀入電腦
Your previous MS-DOS files were not found. 舊的MS-DOS文件沒有找到,這常見於使用雙啟動的系統,另一個系統是DOS6
Your previous MS-DOS version is not supported. MS-DOS startup failed 舊的MS-DOS版本不支持。MS-DOS啟動失敗
Now loading your previous version of MS-DOS, please wait 現在正在載入舊的MS-DOS版本,請等待
Invalid setting in the MSDOS.SYS file:An internal stack overflow has caused this session to be halted MSDOS.SYS文件中無效的設置選項。系統堆疊溢出,系統掛起
Change the STACKS setting in your CONFIG.SYS file, and then try again 請改變CONFIG.SYS文件中的STACK設置,然後再試
Stack overflow 堆疊溢出
Integer divide by 0  整數被0除
Not enough space for environment  沒有足夠的空間
Run-time error 執行錯誤
Floating-point support not loaded  浮點運算支持沒有裝入
Null pointer assignment  無效的中斷點分配


BIOS中的提示訊息
Drive A error 驅動器A錯誤
System halt 系統掛起
Keyboard controller error 鍵盤控制器錯誤
Keyboard error or no keyboard present 鍵盤錯誤或者鍵盤不存在
BIOS ROM checksum error BIOS ROM 校驗錯誤
Single hardisk cable fail 當硬碟使用Cable選項時硬碟安裝位置不正確
FDD Controller Failure BIOS 軟碟控制器錯誤
HDD Controller Failure BIOS 硬碟控制器錯誤
Driver Error 驅動器錯誤
Cache Memory Bad, Do not Enable Cache 高速快取記憶體Cache損壞,不能使用
Error: Unable to control A20 line 錯誤提示:不能使用A20地址控制線
Memory write/Read failure 記憶體讀寫失敗
Memory allocation error 記憶體定位錯誤
CMOS Battery state Low CMOS沒電了
Keyboard interface error 鍵盤接頭錯誤
Hard disk drive failure 載入硬碟失敗
Hard disk not present 硬碟不存在
Floppy disk(s) fail (40) 軟碟驅動器載入失敗,一般是資料線插反,電源線沒有插接,CMOS內部軟式磁碟機設置錯誤
CMOS checksum error-efaults loaded. CMOS校驗錯誤,裝入預設(預定)設置
BIOS重新整理失敗後,Bootblock啟動時出現的提示訊息
Detecting floppy drive A media... 檢測軟式磁碟機A的格式
Drive media is : 1.44Mb1.2Mb 720Kb 360K 驅動器格式是1.44Mb、12Mb、720kb、360kb的一種
DISK BOOT FAILURE, INSERT SYSTEM DISK AND PRESS ENTER 磁碟啟始失敗,插入系統硬碟後按任意鍵繼續
MBR主啟始區提示訊息
Error loading operating sy stem 不能裝入啟始系統
Missing operating system 系統啟始文件丟失
  說明:如果在電腦啟動過程中,在硬體配置清單下方(也就時在平時正常啟動時出現Starting Windows 98…的地方)出現不可識別字元,此時可判斷硬碟分區表損壞。如果你的硬碟上有重要資料,這時你不要輕易進行分區,可找專業的資料恢復公司。
DOS活動分區中的提示訊息
Invalid system disk 無效的系統硬碟
Disk I/O error, Replace the disk and press any key. 磁碟I/O錯誤,替換磁碟後按任意鍵(當C硬碟系統文件丟失或被破壞時出現該提示訊息。這時可能SYS C:為修復系統文件)
Invalid Media Type reaching Drive C: 無效的C盤媒體格式說明。也就是C硬碟沒有格式化或者是其他操作系統的磁碟格式如NTFS
Invalid Boot Diskette Boot Failure 無效的啟動碟,啟動失敗
IO.SYS中的提示訊息
Insert diskette for drive and press any key when ready 插入磁碟到驅動器中後按任意鍵
Your program caused a divide overflow error
If the problem persists, contact your program vendor 你的程式導致溢出錯誤。如果該問題還存在,請聯繫你的程式供應商
Windows has disabled direct disk access to protect your long filenames Windows不能直接訪問受保護的長文件名
The system has been halted. Press Ctrl+Alt+Del to restart your computer 系統掛起,按
Ctrl+Alt+Del重新啟動你的電腦
You started your computer with a version of MS-DOS incompatible with this version of Windows. Insert a Startup diskette matching this version of Windows and then restart 你啟動的MS-DOS版本與Windows版本不相容,請插入與Windows版本匹配的系統硬碟後再重啟
This version of Windows requires a 386 or better processor 該Windows版本需要386以後的CPU支持
A20 hardware error. Contact technical support to identify the problem 地址線A20錯誤。聯繫技術支持來識別該問題
Starting Windows 98... 正在啟動Windows 98……
Windows 98 is now starting your MS-DOS-based program Windows 98正在啟動基於MS-DOS的程式
Windows 98 is now restarting... Windows 98正在重新啟動
Press Esc now to cancel MS-DOS mode and restart Windows 98... 按Esc退出MS-DOS 模式,重新啟動 Windows 98…
There is an unrecognized command in your CONFIG.SYS file 在你的CONFIG.SYS文件中有不可識別的命令
The following command in your CONFIG.SYS file is incorrect: 在你的CONFIG.SYS有下列錯誤命令
The sector size specified in this file is too large: 該文件中指定的扇區太大 The following file is missing or corrupted: WIN.COM COMMAND.COM 下列文件丟失或被破壞:WIN.COM和COMMAND.COM
There is an invalid country code or code page in your CONFIG.SYS file 在你的CONFIG.SYS裡有一個無效的國家代碼
There is an error in the COUNTRY command in your CONFIG.SYS file 在你的CONFIG.SYS裡有一個錯誤的設置國家命令
There is not enough memory for the COUNTRY.SYS file 沒有足夠的記憶體來載入COUNTRY.SYS文件 Remove some drivers from your CONFIG.SYS file, and then try again 請從CONFIG.SYS文件中刪除部分驅動程式,然後再試
Remove some drivers, and then try again 去除一些驅動程式,然後再試。這裡的驅動程式是指在CONFIG.SYS中使用device或devicehigh命令載入的程式文件
Remove some disk drivers from your CONFIG.SYS file, and then try again 從你的(CONFIG.SYS)移去部分程式,然後再試
The configuration specified in your CONFIG.SYS file is too large for memory 調整你的CONFIG.SYS文件以獲得足夠大的記憶體
You have too many block devices specified in your CONFIG.SYS file 調整你的CONFIG.SYS文件以獲得block devices
The STACKS setting(s) in your CONFIG.SYS file are incorrect 在你的CONFIG.SYS中堆疊設置不正確
Default stack settings will be used instead 預設的堆疊設置將被替代使用
There is an error in your CONFIG.SYS file on line XX 在你的CONFIG.SYS裡XX行錯誤
Warning: Logical drives past Z exist and will be ignored 警告:邏輯驅動器Z已經存在,將被忽略
Type the name of the Command Interpreter (e.g., C:\WINDOWS\COMMAND.COM) Press any key to continue… 請輸入命令解釋器的文件名(如:C:\WIN DOWS\COMMAND.COM)後,按任意鍵繼續
Windows is bypassing your startup files Minimal network support will be loaded if available Windows正在跳過你的啟動文件。如果網路可用,最小網路支持將被載入
Windows is starting the command prompt only Windows正在啟動命令字元模式
Windows will prompt you to confirm each startup command Windows將提示你確認每一個啟動命令
The compression driver cannot be set up correctly 壓縮驅動程式不能被正確載入
Get a version from your vendor that is compatible with this version of Windows 從你的供應商那裡獲得一個與Windows版本相相容的版本
Process the system registry 執行系統註冊表
Create a startup log file (BOOTLOG.TXT) 創建啟動日誌BOOTLOG.TXT文件
Process your startup device drivers (CONFIG.SYS) 執行CONFIG.SYS文件中的設備驅動
Process your startup command file (AUTOEXEC.BAT) 執行AUTOEXEC.BAT中的啟動命令
Load the Windows graphical user interface 裝入WINDOWS圖形用戶界面(GDI)
Warning: Windows has detected a registry/configuration error. Choose, Command prompt only, and run SCANREG 警告:Windows檢測到一個註冊表或配置錯誤選擇DOS操作模式,執行SCANREG
Warning: Windows has detected a compressed drive access error. Choose Safe mode command prompt only, to help you identify the problem 警告:Windows檢測到一個訪問壓縮驅動器錯誤,選擇安全模式下的MS-DOS,來幫助你識別這個問題
Warning: Windows did not finish loading on the previous attempt. Choose Safe mode, to start Windows with a minimal set of drivers 警告:Windows在剛才嘗試後不能夠完成載入,選擇安全模式,用最小驅動啟動你的電腦
Warning: Windows multi-boot may not function correctly Check for system files in your root directory with conflicting extensions 警告:Windows不能夠正確完成多系統啟動,在你的ROOT目錄裡檢查不一致的系統文件
Warning: the system configuration manager failed to run. Some of your real-mode device drivers may not initialize properly 警告:系統管理器執行失敗,一些實模式驅動可能沒有正確初始化
The BUFFERS setting(s) in your CONFIG.SYS file are too large. Default buffer settings will be used instead 在你的CONFIG.SYS裡BUFFER設置太大。預定的BUFFER緩衝器設置將被使用
A memory allocation error occurred during startup >Restart your computer and select Interactive Start to identify the problem 在啟動過程中記憶體分配發生錯誤,請重新啟動你的電腦然後選用交互式方式啟動來確定故障原因
Warning: the high memory area (HMA) is not available Additional low memory (below 640K) will be used instead 警告:高端記憶體不可用,低端記憶體將被代替使用
There is not enough memory for Windows. Remove some drivers from your CONFIG.SYS file, and then try again 對Windows來說沒有足夠的記憶體,請從CONFIG.SYS文件中移去部分載入的程式,然後再試著啟動你的讀入電腦
Your previous MS-DOS files were not found. 舊的MS-DOS文件沒有找到,這常見於使用雙啟動的系統,另一個系統是DOS6
Your previous MS-DOS version is not supported. MS-DOS startup failed 舊的MS-DOS版本不支持。MS-DOS啟動失敗
Now loading your previous version of MS-DOS, please wait 現在正在載入舊的MS-DOS版本,請等待
Invalid setting in the MSDOS.SYS file:An internal stack overflow has caused this session to be halted MSDOS.SYS文件中無效的設置選項。系統堆疊溢出,系統掛起
Change the STACKS setting in your CONFIG.SYS file, and then try again 請改變CONFIG.SYS文件中的STACK設置,然後再試
Stack overflow 堆疊溢出
Integer divide by 0  整數被0除
Not enough space for environment  沒有足夠的空間
Run-time error 執行錯誤
Floating-point support not loaded  浮點運算支持沒有裝入
Null pointer assignment  無效的中斷點分配
COMMAND中的提示訊息
Stack overflow 堆疊溢出
Integer divide by 0 分母是0
Not enough space for environment 磁碟沒有足夠的空間
Run-time error 時鐘錯誤
No fixed disks present 沒有硬碟存在
Insufficient memory 記憶體不足
Invalid drive specification 無效的驅動器名
Invalid characters in volume label 無效的磁碟代號
Invalid Volume ID 無效的卷標ID號
No target drive specified 目標驅動器沒有定義
missing operating system 系統文件丟失
Non system Disk or Disk Error 不是系統硬碟或磁碟錯誤
Replace Disk and Press Anykey To Reboot 替換磁碟,按任意鍵重新啟動
SYS傳送系統文件時的提示訊息
Cannot find System Files 不能找到系統文件
System transferred 系統傳送完畢
Disk unsuitable for system disk 目標磁碟不適合做系統硬碟


所有時間均為台北時間。現在的時間是 08:34 PM

Powered by vBulletin® 版本 3.6.8
版權所有 ©2000 - 2024, Jelsoft Enterprises Ltd.

『服務條款』

* 有問題不知道該怎麼解決嗎?請聯絡本站的系統管理員 *


SEO by vBSEO 3.6.1