史萊姆論壇

史萊姆論壇 (http://forum.slime.com.tw/)
-   軟體應用問題討論區 (http://forum.slime.com.tw/f5.html)
-   -   為何我的系統會變這樣..... (http://forum.slime.com.tw/thread42047.html)

LuckyBird 2003-06-09 11:01 PM

為何我的系統會變這樣.....
 
請問一下,為什麼 系統的 效能中會會出現這樣的字樣?


相容模式的分頁方式降低整體系統效能。
磁碟機 C 正在使用 MS-DOS 相容模式檔案系統。
磁碟機 D 正在使用 MS-DOS 相容模式檔案系統。
磁碟機 E 正在使用 MS-DOS 相容模式檔案系統。
請問一下,為什麼系統 中的 效能 會出現這樣的字樣?

自從我灌了光碟機dos的驅動程式之後,我win98就變這樣了....請問要怎麼改回來??且我系統管理員找不到光碟機,但光碟機卻可以.可是跑的速度...跟以前相比實在差太多...請各位幫幫忙...
我安裝程式後他是怎麼寫的...
Creating Sub-Directory
Copying File ............
Modifying c:\config.sys
Modifying c:\AUTOEXEC.BAT
他的ZIP文件檔....
----- HOW TO INSTALL ATAPI CD-ROM DEVICE DRIVER -----

********************
** Introduction **
********************

This utility installs the CD-ROM device driver needed by your CD-ROM
drive to interface with your PC system. The drive installation disk
includes the following files:

* README.TXT This file
* INSTALL.EXE CD-ROM installation program
* IDE.SYS CD-ROM device driver


********************
** Requirements **
********************

Hardware Requirements :
* IBM PC/AT or 100% compatible
* one free IDE socket
* one IDE CD-ROM drive

Software Requirement:
* MS-DOS version 6.0 or later
* Microsoft Windows 3.1 or later
* MS-DOS CD-Extension (MSCDEX 2.21) or later

*******************************
** Installation Procedures **
*******************************

Follow the steps below to install CD-ROM driver:

1. Restart your computer in DOS mode.
2. Insert the installation disk into your floppy disk drive.
3. Change the directory to that of your floppy disk drive (usually A:),
and type "INSTALL <Enter>" at the DOS prompt.
4. After the installation is complete, reboot your system.

Two files will be modified to include the following lines:

CONFIG.SYS :
DEVICE=C:\CDROM\IDE.SYS /D:IDECD000

AUTOEXEC.BAT :
MSCDEX.EXE /D:IDECD000

NOTE: Make sure you have the file MSCDEX.EXE under your path. Refer
to your DOS manual or the online help for more information.

*************************
** Change Settings **
*************************

Modify the previous two command lines in CONFIG.SYS and AUTOEXEC.BAT
to reconfigure the settings of the CD-ROM driver, and then restart
your system.

To enabling DMA function, change the CONFIG.SYS file as:

DEVICE=C:\CDROM\IDE.SYS /D:IDECD000 [/DMA] [/P:xxx,yy]

"/DMA" enables BUS MASTER function if your mother board supports this
function.
"/UDMA" enables ULTRA DMA function if your mother board supports this
function.
"/q" or "/Q" enable quick mode. (Default)

Example:
DEVICE=C:\CDROM\IDE.SYS /D:IDECD000 /q /DMA /P:1F0,14

The option "/P:" specifies the I/O port address and IRQ level.
The number xxx in hex specifies the I/O port address (such as 1F0,
170, 1E8, or 168 in HEX), and yy specifies the IRQ level (such as
14, 15, 11, or 10 in decimal).

Note:
Please do not add /P option if you are not familiar with I/O port
address and IRQ level.

Changing the AUTOEXEC.BAT file :

MSCDEX /D:driver [/E] [/K] [/S] [/V] [/L:letter] [/M:number]

Example:
MSCDEX /D:IDECD001 /L:G /M:10

For more information, please refer to MS-DOS online help for MSCDEX
by typing HELP MSCDEX.
看的懂得高手請幫幫忙吧..謝!!


所有時間均為台北時間。現在的時間是 04:42 PM

Powered by vBulletin® 版本 3.6.8
版權所有 ©2000 - 2025, Jelsoft Enterprises Ltd.

『服務條款』

* 有問題不知道該怎麼解決嗎?請聯絡本站的系統管理員 *


SEO by vBSEO 3.6.1