請問一下,為什麼 系統的 效能中會會出現這樣的字樣?
相容模式的分頁方式降低整體系統效能。
磁碟機 C 正在使用 MS-DOS 相容模式檔案系統。
磁碟機 D 正在使用 MS-DOS 相容模式檔案系統。
磁碟機 E 正在使用 MS-DOS 相容模式檔案系統。
請問一下,為什麼系統 中的 效能 會出現這樣的字樣?
自從我灌了光碟機dos的驅動程式之後,我win98就變這樣了....請問要怎麼改回來??且我系統管理員找不到光碟機,但光碟機卻可以.可是跑的速度...跟以前相比實在差太多...請各位幫幫忙...
我安裝程式後他是怎麼寫的...
Creating Sub-Directory
Copying File ............
Modifying c:\config.sys
Modifying c:\AUTOEXEC.BAT
他的ZIP文件檔....
----- HOW TO INSTALL ATAPI CD-ROM DEVICE DRIVER -----
********************
** Introduction **
********************
This utility installs the CD-ROM device driver needed by your CD-ROM
drive to interface with your PC system. The drive installation disk
includes the following files:
* README.TXT This file
* INSTALL.EXE CD-ROM installation program
* IDE.SYS CD-ROM device driver
********************
** Requirements **
********************
Hardware Requirements :
* IBM PC/AT or 100% compatible
* one free IDE socket
* one IDE CD-ROM drive
Software Requirement:
* MS-DOS version 6.0 or later
* Microsoft Windows 3.1 or later
* MS-DOS CD-Extension (MSCDEX 2.21) or later
*******************************
** Installation Procedures **
*******************************
Follow the steps below to install CD-ROM driver:
1. Restart your computer in DOS mode.
2. Insert the installation disk into your floppy disk drive.
3. Change the directory to that of your floppy disk drive (usually A

,
and type "INSTALL <Enter>" at the DOS prompt.
4. After the installation is complete, reboot your system.
Two files will be modified to include the following lines:
CONFIG.SYS :
DEVICE=C:\CDROM\IDE.SYS /D:IDECD000
AUTOEXEC.BAT :
MSCDEX.EXE /D:IDECD000
NOTE: Make sure you have the file MSCDEX.EXE under your path. Refer
to your DOS manual or the online help for more information.
*************************
** Change Settings **
*************************
Modify the previous two command lines in CONFIG.SYS and AUTOEXEC.BAT
to reconfigure the settings of the CD-ROM driver, and then restart
your system.
To enabling DMA function, change the CONFIG.SYS file as:
DEVICE=C:\CDROM\IDE.SYS /D:IDECD000 [/DMA] [/P:xxx,yy]
"/DMA" enables BUS MASTER function if your mother board supports this
function.
"/UDMA" enables ULTRA DMA function if your mother board supports this
function.
"/q" or "/Q" enable quick mode. (Default)
Example:
DEVICE=C:\CDROM\IDE.SYS /D:IDECD000 /q /DMA /P:1F0,14
The option "/P:" specifies the I/O port address and IRQ level.
The number xxx in hex specifies the I/O port address (such as 1F0,
170, 1E8, or 168 in HEX), and yy specifies the IRQ level (such as
14, 15, 11, or 10 in decimal).
Note:
Please do not add /P option if you are not familiar with I/O port
address and IRQ level.
Changing the AUTOEXEC.BAT file :
MSCDEX /D:driver [/E] [/K] [/S] [/V] [/L:letter] [/M:number]
Example:
MSCDEX /D:IDECD001 /L:G /M:10
For more information, please refer to MS-DOS online help for MSCDEX
by typing HELP MSCDEX.
看的懂得高手請幫幫忙吧..謝!!