沒想到華X也有這種貨色.....他這種說法不是自打嘴巴嗎?

華X技術支援官網明明就寫著A7A133/266只要更新BIOS到某版本後
均支援48bit定址，如果不支援公司會標示有支援?

而且它系統已經正確辨識出硬碟的廠牌、型號、容量了，而且格式化後
容量都是正確的。只是運作變成以PIO模式運作效能大減.......

他身為工程師卻用這種說法搪塞，這跟聯X修理手機修不好的一律用"
主機板潮濕、侵蝕，人為因素"當藉口要求對方付費維修；電腦門市
工程部(汽車保養廠)修不好的一律用"換字訣"處理一樣嗎?搞到最後
換的零件都可以另外湊一台電腦了.......

他這種講法我唾棄他，遠不如一句"先生我建議您可以考慮額外安裝一
張IDE(SATA)擴充卡試試看"來的有建設性........

或者說華X工程師摸烙鐵比較內行，故障排除就比較兩光了....

在他們的討論區有人說應該不會有問題,用了他給的驅動後只是前面120G可以給它跑到DMA模式,而後面的磁區可能只能跑PIO、不知道真實情況是不是這樣?請教各位有可能是這樣麼?不然、就得等自己做測試了.....
謝謝!

雖然、華X最後的這位工程師給我的答案,我是非常不滿意,但就整體的客服還算不錯,讓我問了將近半天的時間,至少前面幾位的態度還十分不錯（雖然花了好多時間,也沒有不耐煩的氣息）,這點我還是給予肯定,當然啦,最後的總結還是失望的....
如果您們有空...根據各位的了解....可以請教一下上面的說法嗎?倒底超過了120G以後的磁區是 1:可能資料易失,還是 2:只能跑PIO模式而已,如果是2那還勉強......

非常感謝上面給予建議的諸位先輩!!

要構成120GB這部份消失、出問題只有一個方法.....

那就是晶片組不支援48bit定址能力....

比方說張三拿李四的500GB硬碟回家copy DVD，結果張三主機板與OS環境
並未支援48bit定址模式，這時李四的120GB以後的空間運作會出問題，不是
分割區消失就是檔案搬移錯誤.....

如果你吃飽沒事可以到VIP會員軟體分享區下載飛鳥版主分享的XP-SP2原版
光碟來安裝，這是最"正莊"的XP系統安裝片。安裝之後看會不會有問題，XP
要開啟支援48bit定址有一些條件，我不知道那種"蝦米碗糕整合版"是不是有
針對這方面開啟支援.....

如果安裝飛鳥版的XP還是無法跑DMA模式，那乾脆買擴充卡取代原有的IDE
介面使用比較省力啦......畢竟你這主機板屬於冷門的版，在K7時代都以VIA
晶片組為大宗，你這ALI的算是小眾市場...我找很多資料似乎只有華碩出..

A老大您上面提到的這個擴充卡是指利用PCI插槽,可以轉成IDE硬碟用的那種卡嗎?

1.這樣子不支援高容量硬碟的主機就可以使用大容量的硬碟了嗎?
2.硬碟效能會比較低嗎?
3.會降低整体性能嗎?
4.不知道相容性好不好?
5.裝置管理員的設置也相同嗎?
6.大約多少＄

另外可否幫我看一下我所裝的IDE驅動的內容,它倒底在講啥?英文不識幾個真頭疼
***********************************************
ALi Ultra IDE Driver for Win2000/XP
***********************************************

------------
INTRODUCTION
------------

This file contains a variety of information you should read before
installing ALi Ultra IDE driver. ALi Ultra IDE driver is
a driver for NT5 Architecture (e.g., Windows 2000 and XP).
It supports hard drive which has size larger than 128GB (1G=2 ^ 30).
It also supports ATA133 hard drive for better disk performance
(ALi M1535+, 1535D+ chips support ATA133 feature).

ALi Corporation does not guarantee that this Ultra IDE driver
will work on your motherboard. If you meet any problem, you can go to
ALi web site Support Page to fill CORE LOGIC FORM for problem feedback.

----------------------------
1. Installation Instructions
----------------------------

Windows 2000
(1) Run integrated driver .exe file
(2) Click "Next" to continue
(3) Select "ALi Ultra IDE Driver", and then "Next"
(4) Click "Yes" to continue installation, and then "Finish" to restart your system
(5) After booting into Win2000, OS will detect first IDE channel
(6) Click "Next" to continue
(7) Click "Next" to search driver
(8) Uncheck all item, then click "Next", "Next" to continue installation
(9) Click "Finish", then click "No" to continue
(10) Then OS will detect second IDE channel
(11) Click "Next" to continue
(12) Click "Next" to search driver
(13) Uncheck all item, then click "Next", "Next" to continue installation
(14) Click "Finish", then click "Yes" to restart system

Windows XP
(1) Run integrated driver .exe file
(2) Click "Next"
(3) Select "ALi Ultra IDE Driver", and then "Next"
(4) Choose "Continue Anyway", and then "Finish" to restart your system
(5) After booting into XP, OS will detect first IDE channel and then notify you
to restart system (Be patient to wait for OS to notify you to restart system.
If you restart system by yourself before OS notification, unknown result may occur)
(6) Click "Yes" to restart system
(7) After booting into XP, OS will detect second IDE channel and then notify you
to restart system (Be patient to wait for OS to notify you to restart system.
If you restart system by yourself before OS notification, unknown result may occur)
(8) Click "Yes" to restart system


------------------------------
2. Uninstallation Instructions
------------------------------

Use control panel :
1. Open "Control Panel" folder
2. Invoke "Add/Remove Programs" icon
3. Choose "ALi Ultra IDE Driver" item
4. Click on "Change/Remove" button to remove driver.

-----------------------
3. IDE Set Mode Utility
-----------------------

This utility is used to set device timing mode as PIO, DMA, or Ultra DMA.
Its main purpose is to solve some device "compatibility" problems.

For example, your CDROM drive reports its capability that it can run "DMA"
and "PIO" timing mode.
Due to device firmware bug or some other reason, this device cannot work on DMA mode.
In this case, you can run "IDE Set Mode Utility" to set device timing mode as PIO.

The utility is in "Start->Programs->ALi Products->IDE Set Mode Utility".

After you run it, you can use its default setting with "Auto" checked.
When "Auto" is checked, device will run its best timing mode.

In this case, if you want to change device timing mode as PIO, you can uncheck "Auto"
item and then move mouse cursor to click on slider bar, draw it to "PIO".
After you change timing mode and click "OK", you will be notified to "Restart" your
system for this new setting to work.

You can control each device to run at different timing mode by clicking on "DEV0", "DEV1"
, "DEV2" and "DEV3".

When "Auto" is checked, device will run its best timing mode.
When "Auto" is unchecked, you can move mouse cursor to click on slider bar, draw it to
different timing mode like "PIO", "DMA", "UDMA33", "UDMA66", "UDMA100/133".

"Running Mode" means the current timing mode of the selected device (DEV0/DEV1/DEV2/DEV3).

Notice:
1. If you see these two IDE controllers become "SCSI/RAID Host Controller" in Windows
"Device Manager", this is normal, don't worry. Since "ALi Ultra IDE Driver" is used
to mimic IDE devices as SCSI devices. Therefore you will find your IDE devices
becoming SCSI devices in "Device Manager"
2. In order to get better IDE performance and signal quality, if your motherboard supports
UDMA66 or UDMA100/133, we strongly suggest you to use 80-wire IDE cable.
If your motherboard only supports UDMA33, you can just use 40-wire IDE cable.

v4.008
Release Notice:
1. In Win2000/XP, Standby and Hibernation can be enabled by following steps.
(1) Run "regedit.exe"
(2) Click on
HKEY_LOCAL_MACHINE/SYSTEM/CurrentControlSet/Services/alihdd/Parameters/PnpInterface/5
And "Edit->Rename" to change Name from 5 to 1
(3) "Restart" system to take effect.
2. To avoid Nero CD speed problem:
(1) Try to connect CD, CDRW or DVD drive on the same IDE channel
(2) Don't connect HDD with CD/CDRW/DVD on the same IDE channel


謝謝!!

沒錯，就是PCI介面的....

1.這樣子不支援高容量硬碟的主機就可以使用大容量的硬碟了嗎?
2.硬碟效能會比較低嗎?
3.會降低整体性能嗎?
4.不知道相容性好不好?
5.裝置管理員的設置也相同嗎?
6.大約多少＄

1.沒錯，有的主機板不支援高容量硬碟可以買這個取代原來IDE介面。
2.不會...除非你要架設RAID
3.不會
4.沒有相容性問題
5.這就不用管它了
6.大約一千多吧，看你是買純IDE介面還是SATA+IDE介面的....

叫你用擴充卡是死馬當活馬醫，當然條條大路通羅馬。你要換主機板
用也行....甚至升級電腦

我想這問題可能要問問ALI官方，你有空可以嘗試寫信問問看...
那個驅動我記得你測試過了，我叫你裝你說會當機..

不知道您是打哪邊的華碩客服...既然連該位工程師給你的答覆都不是很滿意
要換做是我，我會打去總公司先給他投訴，然後同樣問題再問(俺以前常常幹這種事)
華碩總公司
電話: 02-2894-3447

要讓那顆硬碟能夠正常作用，最省的花費應該同A大所言，買張擴充卡
其實只要買IDE的就好了 ，除非你哪天又想換SATA硬碟裝這張主機板上
可以找拍賣網的
再不然就是找張可以符合你現在CPU規格的中古or庫存主機板了

A7A133/266的問題向Google大神查過了...
目前知道有一個驅動程式（向網友索取中，索取到在上傳給需要的版友）可以讓大容量硬碟辨識為SCSI，以正常運作
但有可能前120G以UDMA模式運作，後面則以PIO模式運作

而據網友所說，ALI官方曾說過要修正此問題，現在都2006年底了，官方還是沒解決=.=

如果只單買IDE擴充卡,那就比較便宜了,我買過680元~~

唉呀~別想那麼多了，你擴充一張IDE或者SATA卡就對了...省時省力

到時候升級那張卡還可以用咧....買了不吃虧(現在晶片組都只有一組IDE通道)

A大的建議~剛抓下飛鳥大的XP純版本,裝了~無效,呵呵!!好了,不想再浪費心力與時間了,就去給它買張IDE擴充卡,(只好犧牲拔下電視卡了),另外熊大所提的驅動程式,我巳有裝,但效果有提升還是有限,不過有需要的人還是可以試試,也許對您剛好有幫助,謝謝史版眾位大大的鼎力幫忙!
感謝各位!

那就是驅動的問題了.....你就這樣處理吧，電視卡應該不用拔下...
你主機板PCI插槽很多.....

建議你考慮一下SATA+IDE這種組合的卡，比較有投資報酬率....

昨天去給它買張IDE擴充卡,才550元（因為找了好幾家都找不到IDE及SATA共卡）還真不錯,速度都還可以,也沒什麼安裝上的困難,早知道就這麼做還一直耗精神....笨!
謝謝A大及眾建言的大大,也希望原發言的樓主獲得解決!

也正在尋覓IDE擴充卡中.....
願早日發現...

PS.台南哪裡有..誰知道...請告訴小弟一聲....=.=

去賣場跟商家講
IDE的硬碟擴充卡 就好了

要像mini大說的~用問的比較快...因為小店大部份沒有....像順X也有在賣,大型的店也有.....但多問幾家小店的結果,同廠牌同型省了150元,多花沒多少時間!

那這篇就討論結束了........

買擴充卡優先選擇SATA1.1+IDE的款式，這樣兩種介面都可以使用。
其次才考慮純IDE介面的卡；這些擴充卡都有支援基礎RAID的功能，
因此都有很不錯的投資報酬率....