|
2006-11-21, 07:48 PM
|
|
|
註冊會員
|
疑問 - 剛買的seagate250G硬碟為什麼跑很慢
請問各位大大~
前天買了一顆seagate/250G/16M/7200RPM的硬碟.裝在電腦上要做備份硬碟 但是不管要複製什麼檔案到那顆硬碟速度都很慢.複製1百多MB的檔案就要跑各3分鐘左右 但是用另外的2顆MAXTOR/60G複製1百多MB的檔案只要幾十秒 本來想說買到壞掉的拿去跟店家再換了一顆.拿回來裝好分割好也是都讀的到 但是又要複製東西的時候又是一樣的情形了 請問這是為什麼 |
|
送花文章: 44,
|
|
2006-11-27, 05:25 PM
|
#31 (permalink) |
|
管理員
 
|
靠~~都被搞混了......亂插花
 1.請檢查A7A266主機板BIOS版本在1011版(含)以後.. 2.將這個下載回來安裝...Integrated220 http://www.nvidia.com/page/uli_drivers.html 3.請補上詳細的零件組態... 感覺似乎是軟體問題，因為你的系統、硬體應該都已經支援高容量硬碟了 |
__________________ 我是史版A大，錢的數量決定電腦的力量  我是給女孩修電腦長大的，經驗豐富技術過硬，就沒有我修不好的電腦 
|
|
|
|
送花文章: 79354,
|
|
2006-11-27, 08:33 PM
|
#32 (permalink) | |
|
註冊會員
|
引用:
2.將這個下載回來安裝....馬上網路當掉....奇怪?(重開機好幾次都不行上網還是GHOST回來的)是A大懲罰我亂插花.....開玩笑的...別介意 3.零件組態...AMD1.7CPU.....640MBRAM.....Gxxxxx-FX5200顯示卡...兩台DVD都是BENQ....POWER銀風暴400W....HD...都是S牌IDE介面320G及40G 另外我朋友說他的硬碟也是PIO模式...也沒有怎麼差.... 又勞架各位了.....謝謝! |
|
|
|
送花文章: 434,
|
|
2006-11-27, 09:20 PM
|
#33 (permalink) | |
|
註冊會員
|
引用:
2. 如果不想這樣搞下去，重灌95%會正常。 3. 目前只要是IDE的控制晶片，都可以用"標準雙通道 ATA/ATAPI 控制器"，只是用更適合的驅動大致上會更好。 4. 只要大量複製檔案就會慢的根龜一樣，那是因為PIO模式的關係。PIO模式在傳遞資料時會詢問CPU；而DMA mode只會跟CPU說，我拿去用了！然後交給DMA控制器去傳資料。所以不會吃掉CPU資源。 5. enjoy-R，你說已經裝過好多次，是說在還沒裝320G硬碟之前嗎？還是說裝了320G硬碟也重灌系統很多次了？ |
|
|
|
送花文章: 3,
|
|
2006-11-28, 02:27 AM
|
#36 (permalink) |
|
管理員
|
我不知道原因在哪~但是問題都是一樣的....
A7A133/266晶片組相同，南橋都用M1535D+支援ATA-133.... 然後華碩官方都指出支援48bit定址，而且的確也可正確使用.... 只是IDE介面卻變成以PIO模式運作16MB/s大大減損該硬碟的 正常效能.... 我在想會不會是這顆硬碟與南橋晶片有"相容性"問題，如果誰可實驗 一下該硬碟在其他電腦上運作正常就好了....(以ATA-100運作) 你們將其PIO模式強設為UDMA會怎樣? |
|
|
送花文章: 79354,
|
|
2006-11-28, 06:05 AM
|
#37 (permalink) | |
|
註冊會員
|
引用:
|
|
|
|
送花文章: 434,
|
|
2006-12-01, 01:42 PM
|
#39 (permalink) |
|
註冊會員
|
跟華X的工程師耗了好久,也用了他給的驅動,結果在裝置管理員變成了沒有主通道及次通道的硬碟(Ali Altra IDE controller),也沒有觀看是否跑ＤＭＡ的地方,不過我到我的電腦~內容~光碟和硬碟都顯示成SICI的了,但是是硬碟的確變快了
華X的工程師說這塊板子最高只支援120G,建議我去更少一點容量的硬碟,才可解決 目前雖然可以用,但是資料如果真的超過了120G就可能有＂危險",請問這樣真的對HD有損壞的可能嗎?還是真的要去換低容量的HD比較保險? 可是已經超過7天了.....嗚...... |
|
|
送花文章: 434,
|
|
2006-12-02, 07:27 AM
|
#41 (permalink) |
|
管理員
|
沒想到華X也有這種貨色.....他這種說法不是自打嘴巴嗎?
華X技術支援官網明明就寫著A7A133/266只要更新BIOS到某版本後 均支援48bit定址，如果不支援公司會標示有支援? 而且它系統已經正確辨識出硬碟的廠牌、型號、容量了，而且格式化後 容量都是正確的。只是運作變成以PIO模式運作效能大減....... 他身為工程師卻用這種說法搪塞，這跟聯X修理手機修不好的一律用" 主機板潮濕、侵蝕，人為因素"當藉口要求對方付費維修；電腦門市 工程部(汽車保養廠)修不好的一律用"換字訣"處理一樣嗎?搞到最後 換的零件都可以另外湊一台電腦了....... 他這種講法我唾棄他，遠不如一句"先生我建議您可以考慮額外安裝一 張IDE(SATA)擴充卡試試看"來的有建設性........ 或者說華X工程師摸烙鐵比較內行，故障排除就比較兩光了.... |
|
|
送花文章: 79354,
|
|
2006-12-02, 12:07 PM
|
#42 (permalink) | |
|
註冊會員
|
引用:
謝謝! |
|
|
|
送花文章: 434,
|
|
2006-12-02, 12:20 PM
|
#43 (permalink) | |
|
註冊會員
|
引用:
如果您們有空...根據各位的了解....可以請教一下上面的說法嗎?倒底超過了120G以後的磁區是 1:可能資料易失,還是 2:只能跑PIO模式而已,如果是2那還勉強...... 非常感謝上面給予建議的諸位先輩!! |
|
|
|
送花文章: 434,
|
|
2006-12-02, 03:12 PM
|
#44 (permalink) | |
|
管理員
|
引用:
那就是晶片組不支援48bit定址能力.... 比方說張三拿李四的500GB硬碟回家copy DVD，結果張三主機板與OS環境 並未支援48bit定址模式，這時李四的120GB以後的空間運作會出問題，不是 分割區消失就是檔案搬移錯誤..... 如果你吃飽沒事可以到VIP會員軟體分享區下載飛鳥版主分享的XP-SP2原版 光碟來安裝，這是最"正莊"的XP系統安裝片。安裝之後看會不會有問題，XP 要開啟支援48bit定址有一些條件，我不知道那種"蝦米碗糕整合版"是不是有 針對這方面開啟支援..... 如果安裝飛鳥版的XP還是無法跑DMA模式，那乾脆買擴充卡取代原有的IDE 介面使用比較省力啦......畢竟你這主機板屬於冷門的版，在K7時代都以VIA 晶片組為大宗，你這ALI的算是小眾市場...我找很多資料似乎只有華碩出.. |
|
|
|
送花文章: 79354,
|
|
2006-12-02, 10:08 PM
|
#45 (permalink) |
|
註冊會員
|
A老大您上面提到的這個擴充卡是指利用PCI插槽,可以轉成IDE硬碟用的那種卡嗎?
1.這樣子不支援高容量硬碟的主機就可以使用大容量的硬碟了嗎? 2.硬碟效能會比較低嗎? 3.會降低整体性能嗎? 4.不知道相容性好不好? 5.裝置管理員的設置也相同嗎? 6.大約多少＄ 另外可否幫我看一下我所裝的IDE驅動的內容,它倒底在講啥?英文不識幾個真頭疼 *********************************************** ALi Ultra IDE Driver for Win2000/XP *********************************************** ------------ INTRODUCTION ------------ This file contains a variety of information you should read before installing ALi Ultra IDE driver. ALi Ultra IDE driver is a driver for NT5 Architecture (e.g., Windows 2000 and XP). It supports hard drive which has size larger than 128GB (1G=2 ^ 30). It also supports ATA133 hard drive for better disk performance (ALi M1535+, 1535D+ chips support ATA133 feature). ALi Corporation does not guarantee that this Ultra IDE driver will work on your motherboard. If you meet any problem, you can go to ALi web site Support Page to fill CORE LOGIC FORM for problem feedback. ---------------------------- 1. Installation Instructions ---------------------------- Windows 2000 (1) Run integrated driver .exe file (2) Click "Next" to continue (3) Select "ALi Ultra IDE Driver", and then "Next" (4) Click "Yes" to continue installation, and then "Finish" to restart your system (5) After booting into Win2000, OS will detect first IDE channel (6) Click "Next" to continue (7) Click "Next" to search driver (8) Uncheck all item, then click "Next", "Next" to continue installation (9) Click "Finish", then click "No" to continue (10) Then OS will detect second IDE channel (11) Click "Next" to continue (12) Click "Next" to search driver (13) Uncheck all item, then click "Next", "Next" to continue installation (14) Click "Finish", then click "Yes" to restart system Windows XP (1) Run integrated driver .exe file (2) Click "Next" (3) Select "ALi Ultra IDE Driver", and then "Next" (4) Choose "Continue Anyway", and then "Finish" to restart your system (5) After booting into XP, OS will detect first IDE channel and then notify you to restart system (Be patient to wait for OS to notify you to restart system. If you restart system by yourself before OS notification, unknown result may occur) (6) Click "Yes" to restart system (7) After booting into XP, OS will detect second IDE channel and then notify you to restart system (Be patient to wait for OS to notify you to restart system. If you restart system by yourself before OS notification, unknown result may occur) (8) Click "Yes" to restart system ------------------------------ 2. Uninstallation Instructions ------------------------------ Use control panel : 1. Open "Control Panel" folder 2. Invoke "Add/Remove Programs" icon 3. Choose "ALi Ultra IDE Driver" item 4. Click on "Change/Remove" button to remove driver. ----------------------- 3. IDE Set Mode Utility ----------------------- This utility is used to set device timing mode as PIO, DMA, or Ultra DMA. Its main purpose is to solve some device "compatibility" problems. For example, your CDROM drive reports its capability that it can run "DMA" and "PIO" timing mode. Due to device firmware bug or some other reason, this device cannot work on DMA mode. In this case, you can run "IDE Set Mode Utility" to set device timing mode as PIO. The utility is in "Start->Programs->ALi Products->IDE Set Mode Utility". After you run it, you can use its default setting with "Auto" checked. When "Auto" is checked, device will run its best timing mode. In this case, if you want to change device timing mode as PIO, you can uncheck "Auto" item and then move mouse cursor to click on slider bar, draw it to "PIO". After you change timing mode and click "OK", you will be notified to "Restart" your system for this new setting to work. You can control each device to run at different timing mode by clicking on "DEV0", "DEV1" , "DEV2" and "DEV3". When "Auto" is checked, device will run its best timing mode. When "Auto" is unchecked, you can move mouse cursor to click on slider bar, draw it to different timing mode like "PIO", "DMA", "UDMA33", "UDMA66", "UDMA100/133". "Running Mode" means the current timing mode of the selected device (DEV0/DEV1/DEV2/DEV3). Notice: 1. If you see these two IDE controllers become "SCSI/RAID Host Controller" in Windows "Device Manager", this is normal, don't worry. Since "ALi Ultra IDE Driver" is used to mimic IDE devices as SCSI devices. Therefore you will find your IDE devices becoming SCSI devices in "Device Manager" 2. In order to get better IDE performance and signal quality, if your motherboard supports UDMA66 or UDMA100/133, we strongly suggest you to use 80-wire IDE cable. If your motherboard only supports UDMA33, you can just use 40-wire IDE cable. v4.008 Release Notice: 1. In Win2000/XP, Standby and Hibernation can be enabled by following steps. (1) Run "regedit.exe" (2) Click on HKEY_LOCAL_MACHINE/SYSTEM/CurrentControlSet/Services/alihdd/Parameters/PnpInterface/5 And "Edit->Rename" to change Name from 5 to 1 (3) "Restart" system to take effect. 2. To avoid Nero CD speed problem: (1) Try to connect CD, CDRW or DVD drive on the same IDE channel (2) Don't connect HDD with CD/CDRW/DVD on the same IDE channel 謝謝!! |
|
|
送花文章: 434,
|
平板模式
